Transport Panel Sections

The Transport panel has different sections that you can show or hide by activating the corresponding options in the Set up Transport Panel pane.

  • To show all Transport panel sections, right-click anywhere on the Transport panel and select Show All.

The following sections are available:

Audio Performance Meter

Audio Performance Meter

The upper bar displays either the current realtime peak or the ASIO-Guard load, depending on which of the two has the higher value. The lower bar shows the hard disk transfer load of the disk engine.

For a more detailed display of realtime peak and ASIO-Guard load, click to open the Audio Performance panel.

Common Record Modes

Common Record Modes

Allow you to determine what happens if you click Record during an audio or MIDI recording, and where to start the recording.

Audio Record Modes

Audio Record Modes

Allow you to select what happens when you record over existing audio events.

MIDI Record Modes

MIDI Record Modes

Allow you to select what happens when you record over existing MIDI parts.

MIDI Auto Quantize

Automatic MIDI Record Quantize

Activates automatic quantizing during a MIDI recording.

Locators

Go to Left Locator Position

Allows you to go to the left locator position.

Left Locator Position

Shows the left locator position.

Go to Right Locator Position

Allows you to go to the right locator position.

Right Locator Position

Shows the right locator position.

Locator Range Duration

Locators to Selection

Allows you to set the locators to the selection.

Locator Range Duration

Shows the duration of the locator range.

Punch Points

Lock Punch Points to Locators

Locks the punch points to the left and right locator positions.

Punch In

Activates Punch In.

Punch In Position

Allows you to set up the punch in position. For this to work, Lock Punch Points to Locators must be deactivated. To show/hide this, click the points on the divider.

Punch Out

Activates Punch Out.

Punch Out Position

Allows you to set up the punch out position. For this to work, Lock Punch Points to Locators must be deactivated. To show/hide this, click the points on the divider.

Transport Controls

Go to Previous Marker/Zero

Moves the project cursor to the previous marker/zero position on the timeline.

Go to Next Marker/Project End

Moves the project cursor to the next marker/project end.

Rewind

Moves backward.

Forward

Moves forward.

Cycle

Activates/Deactivates cycle mode.

Stop

Stops playback.

Start

Starts playback.

Transport Record

Activates/Deactivates record mode.

Time Display

Select Primary Time Format

Allows you to select a time format for the primary time display.

Primary Time Display

Shows the position of the project cursor in the selected time format.

Select Secondary Time Format

Allows you to select a time format for the secondary time display.

Secondary Time Display

Shows the position of the project cursor in the selected time format.

Markers

Jump to Marker

Allows you to set and locate marker positions.

Open Markers Window

Opens the Markers window.

Pre-roll & Post-roll

Activate Pre-roll

Activates pre-roll.

Pre-roll Amount

Allows you to set the pre-roll position. To show/hide this, click the points on the divider.

Activate Post-roll

Activates post-roll.

Post-roll Amount

Allows you to set the post-roll position. To show/hide this, click the points on the divider.

Tempo & Time Signature

Activate Tempo Track

Allows you to activate/deactivate the tempo track.

Tempo

Allows you to set the tempo value.

Time Signature

Allows you to set the first time signature value. To show/hide this, click the points on the divider.

Tap Tempo

Allows you to insert tempo changes into your project by tapping.

Tap Tempo Mode

Defines where new tempo events are inserted.

Activate External Sync

Activate External Sync

Activates external synchronization.

Open Synchronization Setup

Allows you to open the Project Synchronization Setup dialog.

Click & Count-in & Click Pattern

Activate Metronome Click

Activates the metronome click.

Activate Count-in

Activates the metronome click in count-in.

Click Pattern

Allows you to set up a click pattern. To show/hide this, click the points on the divider.

Open Metronome Setup

Opens the Metronome Setup dialog. To show/hide this, click the points on the divider.

Input/Output Activity

MIDI In Activity

Displays the MIDI input signals.

MIDI Out Activity

Displays the MIDI output signals.

Audio Activity

Displays the audio input/output signals.

Audio Clipping

Displays audio clipping.

Level Display

Displays the output level.

Level Control

Allows you to control the output level.