Reverb

The early reflections are responsible for the spatial impression in the first milliseconds of the reverb. For emulating different rooms, you can choose from different early reflection patterns and adjust their size. The reverb tail, or late reverberation, offers parameters for controlling the room size and the reverb time. You can adjust the reverb time individually in three frequency bands.

Predelay

Determines how much time passes before the reverb is applied. This allows you to simulate larger rooms by increasing the time it takes for the first reflections to reach the audience.

Early Reflections

Allows you to select an early reflections pattern. The early reflections pattern contains the most important delays that deliver the key information for the spatial impression of the room.

ER/Tail

Sets the level balance between the early reflections and the reverb tail. With a setting of 50%, early reflections and tail have the same volume. Settings below 50% raise the early reflections and lower the tail. As a result, the sound source moves towards the front of the room. Settings above 50% raise the tail and lower the early reflections. As a result, the sound source moves toward the back of the room.

Delay

Delays the onset of the reverb tail.

Room Size

Controls the dimensions of the simulated room. With a setting of 100%, the dimensions correspond to a cathedral or a large concert hall. With a setting of 50%, the dimensions correspond to a medium-sized room or studio. Settings below 50% simulate the dimensions of a small room or a booth.

Main Time

Controls the overall reverb time of the tail. The higher this value, the longer the reverb tail will decay. With a setting of 100%, the reverb time is infinitely long. The Main Time parameter also represents the mid band of the reverb tail.

High Time

Controls the reverb time for the high frequencies of the reverb tail. With positive values, the decay time of the high frequencies is longer. With negative values, it is shorter. Frequencies are affected depending on the High Freq parameter.

Low Time

Controls the reverb time for the low frequencies of the reverb tail. Positive values result in a longer decay for the low frequencies. Negative values result in a shorter decay.

Frequencies are affected depending on the Low Freq parameter.

High Freq

Sets the cross-over frequency between the mid and the high band of the reverb tail. You can offset the reverb time for frequencies above this value from the main reverb time with the High Time parameter.

Low Freq

Sets the cross-over frequency between the low and the mid band of the reverb tail. The reverb time for frequencies below this value can be offset from the main reverb time with the Low Time parameter.

Show Early Reflections Page/Show Chorusing Page

With these two buttons, you can choose whether to display the early reflections settings or the chorusing settings in the lower left part of the effect panel.

ER Size

Adjusts the length of the early reflections pattern. With a setting of 100%, the pattern is applied with its original length and the room sounds natural to the highest possible degree. With settings below 100%, the early reflections pattern is compressed, and the room is perceived as smaller.

Low Cut

Attenuates the low frequencies of the early reflections. The higher this value, the fewer low frequencies are present in the early reflections.

High Cut

Attenuates the high frequencies of the early reflections. The lower this value, the fewer high frequencies are present in the early reflections.

Shape

Controls the attack of the reverb tail. With a setting of 0%, the attack is more immediate, which is a suitable setting for drums. The higher this value, the less immediate the attack.

Density

Adjusts the echo density of the reverb tail. With a setting of 100%, single reflections from walls cannot be heard. The lower this value, the more audible the single reflections.

Tail High Cut

Attenuates the high frequencies of the reverb tail. The lower this value, the fewer high frequencies are present in the reverb tail.

Width

Adjusts the output of the reverb signal between mono and stereo. With a setting of 0%, the output of the reverb is mono. At 100%, it is stereo.

Mix

Sets the ratio between the dry and the wet signal.

Chorusing

Chorusing allows you to enrich the reverb tail through subtle pitch modulations. To access the chorusing parameters, click the Show Chorusing Page button.

Chorusing On/Off

Activates/Deactivates the chorusing effect.

Chorusing Rate

Specifies the frequency of the pitch modulation.

Chorusing Depth

Sets the intensity of the pitch modulation.