Transport Panel Sections

To show all Transport panel sections, right-click anywhere on the Transport panel and select Show All.

The following sections are available:

Audio Performance Meter

Audio Performance Meter

The upper bar displays either the current realtime peak or the ASIO-Guard load, depending on which of the two has the higher value. The lower bar shows the hard disk transfer load of the disk engine.

For a more detailed display of realtime peak and ASIO-Guard load, click to open the Audio Performance panel.

Common Record Modes

Common Record Modes: Allow you to determine what happens if you click Record during an audio or MIDI recording, and where to start the recording.

Audio Record Modes

Audio Record Modes: Allow you to select what happens when you record over existing audio events.

MIDI Record Modes

MIDI Record Modes: Allow you to select what happens when you record over existing MIDI parts.

MIDI Auto Quantize

Automatic MIDI Record Quantize: Activates automatic quantizing during a MIDI recording.

Locators

Go to Left Locator Position: Allows you to go to the left locator position.
Left Locator Position: Shows the left locator position.
Go to Right Locator Position: Allows you to go to the right locator position.
Right Locator Position: Shows the right locator position.

Locator Range Duration

Locators to Selection: Allows you to set the locators to the selection.
Locator Range Duration: Shows the duration of the locator range.

Punch Points

Lock Punch Points to Locators: Locks the punch points to the left and right locator positions.
Punch In: Activates Punch In.
Punch In Position: Allows you to set up the punch in position. For this to work, Lock Punch Points to Locators must be deactivated. To show/hide this, click the points on the divider.
Punch Out: Activates Punch Out.
Punch Out Position: Allows you to set up the punch out position. For this to work, Lock Punch Points to Locators must be deactivated. To show/hide this, click the points on the divider.

Transport Controls

Go to Previous Marker/Zero: Moves the project cursor to the previous marker/zero position on the timeline.
Go to Next Marker/Project End: Moves the project cursor to the next marker/project end.
Rewind: Moves backward.
Forward: Moves forward.
Cycle: Activates/Deactivates cycle mode.
Stop: Stops playback.
Start: Starts playback.
Transport Record: Activates/Deactivates record mode.

Time Display

Select Primary Time Format: Allows you to select a time format for the primary time display.
Primary Time Display: Shows the position of the project cursor in the selected time format.
Select Secondary Time Format: Allows you to select a time format for the secondary time display.
Secondary Time Display: Shows the position of the project cursor in the selected time format.

Markers

Jump to Marker: Allows you to set and locate marker positions.
Open Markers Window: Opens the Markers window.

Pre-roll & Post-roll

Activate Pre-roll: Activates pre-roll.
Pre-roll Amount: Allows you to set the pre-roll position. To show/hide this, click the points on the divider.
Activate Post-roll: Activates post-roll.
Post-roll Amount: Allows you to set the post-roll position. To show/hide this, click the points on the divider.

Tempo & Time Signature

Activate Tempo Track: Allows you to activate/deactivate the tempo track.
Tempo: Allows you to set the tempo value.
Time Signature: Allows you to set the first time signature value. To show/hide this, click the points on the divider.
Tap Tempo: Allows you to insert tempo changes into your project by tapping.
Tap Tempo Mode: Defines where new tempo events are inserted.

Activate External Sync

Activate External Sync: Activates external synchronization.
Open Synchronization Setup: Allows you to open the Project Synchronization Setup dialog.

Click & Count-in & Click Pattern

Activate Metronome Click: Activates the metronome click.
Activate Count-in: Activates the metronome click in count-in.
Click Pattern: Allows you to set up a click pattern. To show/hide this, click the points on the divider.
Open Metronome Setup: Opens the Metronome Setup dialog. To show/hide this, click the points on the divider.

Input/Output Activity

MIDI In Activity: Displays the MIDI input signals.
MIDI Out Activity: Displays the MIDI output signals.
Audio Activity: Displays the audio input/output signals.
Audio Clipping: Displays audio clipping.
Level Display: Displays the output level.
Level Control: Allows you to control the output level.