Project Setup Dialog

The Project Setup dialog allows you to make general settings for your project.

  • To open the Project Setup dialog, select Project > Project Setup.

  • To open the Project Setup dialog automatically when you create a new project, activate the Run Setup on Create New Project option in the Preferences dialog (General page).

Important

While you can change most Project Setup settings at any time, you must set the sample rate right after creating a new project. If you change the sample rate at a later stage, you must convert all audio files in the project to the new sample rate to ensure that they play back properly.

In the Project Duration section, the following options are available:

Project Start Time

Allows you to specify the start time of the project in timecode format. This also determines the sync start position when synchronizing to external devices.

Project Duration

Allows you to specify the duration of the project.

Project Frame Rate

In the Project Frame Rate section, the following options are available:

Project Frame Rate

Allows you to specify the timecode standard and the frame rate for the project. When synchronizing to an external device, this setting must correspond to the frame rate of any incoming timecode.

Get Frame Rate From Video

Allows you to set the project frame rate to the frame rate of an imported video file.

Audio Pull-up/Pull-down

Allows you to compensate for audio speed changes by an external clock source during film transfers. Whenever you apply an audio pull from an external clock, select the corresponding value from this pop-up menu. This allows Nuendo to recalculate the sample count to match the adjusted sample rate.

Video Pull

Allows you to adjust the video playback speed for film transfers.

Project Time Displays

In the Project Time Displays section, the following options are available:

Display Format

Allows you to specify the global display format for all rulers and position displays in the program, except for the ruler tracks. However, you can make independent display format selections for the individual rulers and displays.

Use Film Pull Factor (-0.1%)

Adjusts the audio playback speed to match the video.

Display Time Offset

Allows you to specify an offset for the time positions in the rulers and position displays to compensate for the Project Start Time setting.

Display Bar Offset

This setting is only used in conjunction with the Bars+Beats display format. Allows you to specify an offset for the time positions in the rulers and position displays to compensate for the Project Start Time setting.

Record File Format

In the Record File Format section, the following options are available:

Sample Rate

Allows you to specify the sample rate at which Nuendo records and plays back audio.

  • If your audio hardware generates the sample rate internally and you select a non-supported sample rate, this is indicated by a different color. In this case, you must set a different sample rate to ensure that your audio files play back properly.

  • If you select a sample rate that your audio hardware supports but that differs from its current sample rate setting, it is automatically changed to the project sample rate.

  • If your audio hardware is externally clocked and receives external clock signals, sample rate mismatches are accepted.

Bit Depth

Allows you to specify the bit depth of the audio files that you record in Nuendo. Select the record format according to the bit depth that is delivered by your audio hardware. The available options are 16 bit, 24 bit, 32 bit, 32 bit float, and 64 bit float.

Note

  • If your audio interface supports a bit depth of 32 bit and you want to maintain this precision in your recordings, select a Processing Precision of 64 bit float in the Studio Setup dialog.

  • When you record with effects, consider setting the bit depth to 32 bit float or 64 bit float. This prevents clipping (digital distortion) in the recorded files and keeps the audio quality very high. Effect processing and level or EQ changes in the input channel are performed in 32-bit float or 64-bit float format, depending on the Processing Precision setting in the Studio Setup dialog. If you record at 16 bit or at 24 bit, the audio is converted to this lower bit depth when it is written to a file. As a result, the signal may degrade. This is independent of the actual bit depth of your audio hardware. Even if the signal from the audio hardware has a bit depth of 16 bit, the signal is 32 bit float or 64 bit float after the effects are added to the input channel.

  • The higher the bit depth value, the larger the files and the more strain is put on the disk system. If this is an issue, lower the record format setting.

Record File Type

Allows you to specify the file type of the audio files that you record in Nuendo.

Note

  • For wave file recordings larger than 4 GB, the EBU RIFF standard is used. If you use a FAT 32 disk (not recommended), audio files are split automatically. In the Preferences dialog, you can specify what happens if your recorded Wave file is larger than 4 GB.

  • You can set up embedded strings in the Preferences dialog.

Project Ownership

In the Project Ownership section, the following options are available:

Author

Allows you to specify a project author that is written into the file when you export audio files and activate the Insert iXML chunk option. You can specify a default author in the Default Author Name field of the Preferences dialog (General—Personalization page).

Company

Allows you to specify a company name that is written into the file when you export audio files and activate the Insert iXML chunk option. You can specify a default company in the Default Company Name field in the Preferences dialog (General—Personalization page).

Other Project Settings

In the Other Project Settings section, the following options are available:

Stereo Pan Law

If you pan a channel left or right, the sum of the left and the right side is higher (louder) than if this channel is panned center. These modes allow you to attenuate signals panned center. 0 dB turns off constant-power panning. Equal Power means that the power of the signal remains the same, regardless of the pan setting.

Volume Max

Allows you to specify the maximum fader level. By default, this is set to +12 dB. If you load projects created with Nuendo versions older than 5.5, this value is set to the old default value of +6 dB.

3D Pan Mode

Sets the pan mode for 3D channel configurations.

Note

When authoring an MPEG-H project, select 3-Layer to make the bottom layer available for panning.

Hermode Tuning

In the Hermode Tuning section, the following options are available:

HMT Type (MIDI only)

Allows you to specify a mode for Hermode tuning of MIDI notes.

HMT Depth (MIDI only)

Allows you to specify the overall degree of retuning.

Project Location

In the Project Location section, the following options are available:

Project Location information

Displays the project location.

Show in Explorer/Reveal in Finder

Opens a file dialog that shows the location of the project file.