VST MultiPanner Plug-in Panel

• To open the VST MultiPanner plug-in panel in a separate window, double-click a miniature view of VST MultiPanner in the Inspector or the MixConsole.

The following settings and options are available:

Show/Hide Extended Display

/

Shows/Hides additional settings and the Rear View pan area for 3D channel configurations.

Bed Mode

Sets the panner to bed mode. This mode allows you to create the channel-based bed mix.

Note

This button is only available if VST MultiPanner is used as channel panner and a Renderer is selected in the ADM Authoring for Dolby Atmos window.

Object Mode

Sets the panner to object mode. This mode allows you to create mixes for object-based content, for example, in Dolby Atmos format.

Note

• This button is only available if VST MultiPanner is used as a channel panner and a Renderer is selected in the ADM Authoring for Dolby Atmos window.

• If VST MultiPanner is used as an insert plug-in, Object Mode is not available.

Movement restriction buttons

Allow you to restrict the movement to one axis when moving the sound source with the mouse.

Note

• The movement restrictions only affect the graphic presentation in the two pan areas. Hence, activating Vertical Movements Only restricts movements to the y-axis in the Top View area and to the z-axis in the Rear View area.

• The movement restriction buttons do not affect the controls in the positioning section below the pan area.

Reset Parameters

Alt/Opt-click this button to reset all panner parameters to their default values.

Input level meter

Shows the input level for all speaker channels. The numeric values above the meters indicate the peak levels registered for the channels.

Position Left/Right Channels Independently

Activate this option to adjust the front left and right input channels independently by dragging.

Top View

Shows the room from the top and allows you to position the sound source by dragging the panning handles.

To zoom out of the pan area, activate Overview Mode.

Speaker channel buttons

The speaker buttons around the pan area represent the output configuration. The buttons allow you to solo, mute, and disable the corresponding channels.

Note

You cannot automate the soloing of output channels.

Output level meter

Shows the output level for all speaker channels. The numeric values above the meters indicate the peak levels registered for the channels.

Left-Right Pan

Sets the position of the signal on the x-axis.

Rear-Front Pan

Sets the position of the signal on the y-axis.

Rotate Signal around Z-Axis

Rotates the sound source around its positioning handle. This option is only available for stereo and multi-channel signals.

Orbit Center

Rotates the sound source, including all input channels and the positioning handle signal, around the center of the room.

Click Counter Shot to rotate the sound source by exactly 180 degrees.

Radius

Sets the distance of the sound source from the center of the room when using Orbit Center.

Center Distribution

Distributes part or all of the center signal to the left and right front speakers.

Note

If Front Divergence is set to 100 %, Center Distribution has no effect.

Front Divergence

Determines the attenuation curve that is used when positioning the sound source on the front x-axis.

Front/Rear Divergence

Determines the attenuation curve that is used when positioning the sound source on the y-axis.

Rear Divergence

Determines the attenuation curve that is used when positioning the sound source on the rear x-axis.

Signal Width

Sets the expansion of the sound source on the x-axis. This parameter is only available for channels with stereo or multi-channel output configurations.

Signal Depth

Sets the expansion of the sound source on the y-axis. This parameter is only available for channels with multi-channel output configurations.

LFE Level

Sets the signal amount that is sent to the LFE (Low Frequency Effects) channel.

• If the selected input already contains an LFE channel (x.1 configuration), it is routed through VST MultiPanner, and LFE Level is used to control the volume of this channel.

• If the selected input does not contain an LFE channel (x.0 configuration), all input channels are evenly distributed to the output LFE channel. In this case, you can use LFE Level to raise the volume of this downmix.

Note

The LFE channel is used as a full-range channel. No low-pass filtering is applied.